Pengaruh Temperatur, Waktu, dan Aditif  Dalam Pembuatan Zircon Micronized

Sajima Sajima; Moch Setyaji

doi:10.55981/eksplorium.2017.3533

Pengaruh Temperatur, Waktu, dan Aditif Dalam Pembuatan Zircon Micronized

Sajima Sajima, Moch Setyaji

DOI: http://dx.doi.org/10.55981/eksplorium.2017.3533

Abstract

ABSTRAK

Penelitian pengaruh temperatur, waktu dan aditif terhadap proses penggilingan dalam pembuatan zircon micronized telah dilakukan. Proses pembuatan zircon micronized diawali dari proses sortir hasil penambangan dilanjutkan dengan benefisiasi, pemanggangan, pelindian, pengeringan dan penggilingan. Hasil penelitian menunjukkan bahwa kondisi proses pemanggangan optimum terjadi pada temperatur 425 °C, selama 25 menit dan menggunakan aditif sebanyak 4%. Pada kondisi proses tersebut diperoleh zircon-micronized (2 µm) sebanyak 92,10% dengan lama penggilingan 10 menit.

ABSTRACT

Research on temperature, time and additives effects on milling process in micronized-zircon production has been conducted. The production of zircon micronized started from sorting process on mining products then followed by beneficiation, roasting, leaching, dryng and milling processes. The results showed that the optimum conditions of the roasting process was at the temperature of 425 °C, in 25 minutes and using 4% additives. In these conditions, micronized zircon (2 µm) obtained as much as 92.10% in10 minutes milling time.

Keywords

aditif; zircon micronized; pemanggangan; temperatur; waktu

Full Text:

PDF (Bahasa Indonesia)

References

[1] H. Poernomo, “Informasi Umum Zirkonium,” Yogyakarta, 2012.

[2] Kementerian ESDM, Peraturan Menteri Energi dan Sumber Daya Mineral no 08 Tahun 2015. Indonesia, 2015.

[3] C. Cameron, “Worldwide Market for Zirconium to Reach 2.6 Million Metric Tons by 2017,” Ceramic Industry, pp. 1–12, 2012.

[4] Soesilowati and S. Hidayati, “Aplikasi Glasir Zirkon Pada Industri Gerabah Keramik di Pagerjuang Bayat,” Informasi Teknologi Keramik & Gelas, 2008.

[5] S. Routray, L. N. Padhi, and T. Bera, “Recovery of Zirkons of South Eastern Coast of India Their Potential as Refractories and Ceramics,” Int. J. Mech. Eng. Technol., vol. 5, no. 5, pp. 73–82, 2014.

[6] S. Lubbe, R. Munsami, and D. Fourie, “Beneficiation of Zircon Sand in South Africa,” J. South. African Inst. Min. Metall., vol. 7A, pp. 583–588, 2012.

[7] E. Snyders, J. H. Potgieter, and J. T. Nel, “The Upgrading of an Inferior Grade Zirkon to Superior Opacifier for Sanitary Ware and Glazers,” J. South African Inst. Min. Metal., 2005.

[8] T. Indrati, Sajima, and Sudaryadi, “Analisis Struktur Mikro Hasil Pemanggangan Pasir Zirkon,” 2005.

[9] R. Liu, J. K. Qu, J. Song, T. Qi, and D. U. Ailing, “No Title,” Ceram. Int., vol. 40, no. 1B, pp. 1431–1438, 2014.

[10] V. Monov, Blagoy, Sokolov, and S. Stoenchev, “Grinding in Ball Mills: Modeling and Process Control,” Cybern. Inf. Technol., vol. 2, pp. 51–68, 2012.

[11] A. Sujatno, R. Salam, Bandriyana, and A. Dimyati, “Studi Scanning Zirkonium,” J. Forum Nukl., vol. 9, no. 2, pp. 44–50, 2015.